Swimming Pool Time Switch - Intermatic Replacement Timers

Swimming Pool Timers
General Information

Having your filter pump operate on a pool timer saves energy. Most pools don’t need sanitizing, filtering, and circulation 24 hours a day. Swimming pools are designed to “turn over” the water in the pool for approximately 8 hours at a time. We typically use pool timers to operate 10-14 hours per day, depending upon the efficiency of the system, the ambient air temperature, amount of sunlight and the usage that the pool receives.

Setting a Precision pool timer is simple. Inside the enclosure you’ll see a 24 hour dial. There are four “tripper pins” on the dial, two on and two off. The on tripper pin allows power to the filter pump and the other tripper pin turns the switch off, stopping power from going past the timer to the filter pump. More than one set of tripper pins allows you to run the pump in the morning and then late in the afternoon to avoid peak usage times.

Energy Efficiency Pool Tips
To get the maximum energy efficiency out of your swimming pool we suggest the following energy saving tips.

Check the pool timer settings and operations on a regular basis.
Schedule regular check-ups for your natural gas, pool/spa heaters, pool/spa pump and motor.
Routinely inspect thermostat settings.
Clean your filtration system regularly and always follow manufacturer’s instructions.

Pool Timers
Model

Compatible Series Intermatic® Replacement Pool Timers

General Purpose 24-Hour Pool Timers with
Non-Corrosive Enclosure

2 Circuit Swimming Pool Time Switch with
Non-Corrosive Enclosure

Two-In-One Swimming
Pool Timer Switch with
Non-Corrosive Enclosure

Spring Wound Timers
15/30/60 min. or 12 hr.
Aluminum or Decor White

Overview

About our pool timers

Wiring Diagrams

Pool timers reference guide

Pool timers Installation

® Intermatic is the registered trademark of Intermatic Corporation

Swimming Pool Timers

By setting your swimming pool timer to operate your pump during off-peak times, you’re helping to lower the cost of energy.

How to change swimming pool timers setting

Before attempting any adjustment of your swimming pool timer switch settings you must turn off the power by opening the branch circuit breaker that serves the swimming pool timer.

Turn off power by opening the circuit breaker at your electrical panel.
To re-set “on” and “off” times, open the pool timer enclosure and loosen the trip pin enough to slide the tripper around the pool timer dial.
Set the tripper pin (labeled “on” to the desired “on” position (a.m. or p.m.) and re-tighten tripper pin.
Move the off tripper pin similarly to desired off time (a.m. or p.m.), and re-tighten tripper pin.
Set time of day by turning pool timer dial clockwise until correct time (a.m. or p.m.) is in line with pool timer pointer. Do not attempt to move the pointer.
Close the pool timer switch enclosure and turn the power back on.

pool timers
Supplying high quality pool timers to the swimming pool market for over 40 years.
All pool timers are U.L. listed 40 amps.

Our pool timers product line includes:

Direct Intermatic replacement Pool Timers for Intermatic Models: T102, T102, T103, T104, T101R, T102R, T103R, T104R, T101P, T102P, T103P and T104P.

2 Direct Swimming Pool Timers with weather delay circuit or “Fireman’s Switch” replaces Intermatic Pool Timer Models: T101R-201 and T104R-201.

General Purpose 24 Hour Pool Timesr with NEMA III weatherproof enclosure. Replaces Intermatic Pool Timer Models: T101R, T102R, T103R, T104R, T101P, T102P, T103P and T104P.
pool timer

pool timers
pool timer
swimming pool timers
swimming pool timer
Intermatic replacement timers
pool time switch
Intermatic replacement pool timers
Intermatic replacement pool timer

Compatible Series Intermatic® Replacement Pool Timers
General Purpose 24-Hour Pool Timers with Non-Corrosive Enclosure
2 Circuit Swimming Pool Time Switch with Non-Corrosive Enclosure
Two-In-One Swimming Pool Timer Switch with Non-Corrosive Enclosure
About our pool timers
Swimming Pool Timer Wiring Diagrams